VMP 163R Super Monoblade throttle body with Left-hand motor for Odin/Loki supercharger system.  Max-effort 1000+rwhp (see disclaimer at bottom).
 

• Simple bolt-on installation 
• May be used with Cobrajet intake using adapter plate VMP-INA021
• NO ADAPTER BOX required 
• Comes assembled and tested with factory digital electronics 
• Uses native 2015-2017 electronics for ease of tuning 
• Elliptical Monoblade design provides for a combination of high flow and tune-ability 
• Recommended for power adder applications in the 1000+ rwhp range 

Size and fitment: 

• Based on the GT500 bolt-pattern 
• Opening shape is based on the VMP Gen3R  and Odin supercharger 
• Elliptical blade measures 82 mm tall x 153 mm wide 
• The “163” designates the surface area of the opening. Measuring and naming throttle bodies by blade width is not accurate for flow potential, especially when the blade shape is not a true oval. VMP has chosen to designate their line of monoblade throttle bodies by surface area. 

Modern supercharged engines can make over 1000 rwhp. Most customers targeting these power levels go for the biggest throttle body available on the market. They are very disappointed when they find their setup is difficult to tune and drive with these huge throttle bodies. 

Designed to make big power while avoiding the tuning issues many of the larger throttle bodies have, the VMP 163R throttle body is a great solution for those running a power adder on their Mustang or F-150 and want to push it to 1,000+ rwhp. 

Custom designed and properly tuned, the VMP 163R is large enough to make power, but not so large that the fly by wire electronics cannot control the blade. This avoids a “failsafe” condition often indicated by a wrench light on the dash with throttle bodies that are too large. 

Created for high-power applications, the VMP 163R should only be used on builds where the extra size and flow is needed. 

Built with the same electronics found on 2015-2017 Ford Mustangs and F-150s (designated by an F on the motor cover), the VMP 163R monoblade throttle body comes with electronics preinstalled, tested, and set. Simply bolt the VMP throttle body onto the vehicle and load the proper tune. 

The VMP 163R monoblade throttle body may require special tuning such as minimum throttle angle (.80*) and current limit increases. Recommended for heavily modified engines such as those with aftermarket camshafts. The increased lift and duration of aftermarket cams will reduce engine vacuum, making large throttle bodies much smoother and easier to tune. May idle high (~900 rpm) on stock camshaft engines. 
TUNING INFORMATION:

Recommended for heavily modified engines such as those with aftermarket cam shafts. The increased lift and duration of aftermarket cams will reduce engine vacuum, making large throttle bodies much smoother and easier to tune. 
The VMP 163R monoblade throttle body requires special tuning such as:

• Min throttle angle set to 0.80*
• 800-950 RPM minimum idle speed 
• Factory 15-17 gear ratio and TPCC config parameters
• Correct Open Loop Feed Forward and Effective Area Tables
  • Click HERE to download SCT .mvf file for VMP 163RF
     
  • Click HERE to download HP data for VMP 163RF

VMP makes this information available, however, if the rest of the tune is not done properly, correct throttle body data alone will not fix the tune problems.
 

Other signs of improper tuning or a throttle body that is too large: 
 

• P2112 throttle actuator control system stuck closed o Occurs because the computer is having trouble opening or closing a large blade 
• “Wrench light” or “failsafe mode” computer detects a tuning or mechanical issue with the drive by wire system 
• Also, P2104, P2111, P2110, P060B  

Includes: VMP 163R Super Monoblade throttle body for 2015-2017 5.0 L 
Weight: 5.75 lbs.