Home > Mustang Parts > '94-'04 Mustang > 03-04 Cobra Terminator > Supercharger Upgrade >

VMP 2.3L TVS Supercharger Upgrade for 2003-2004 Cobra Mustang (Discontinued)
VMP 2.3L TVS Supercharger Upgrade for 2003-2004 Co

Alternative Views:

Suggested Retail Price: $2,999.00

Availability: Discontinued
Product Code:

Add cap for EGR bung?*:

Add contoured EGR spacer?*:

Add Second Pulley?*:

Add Third Pulley?*:

Inlet Elbow?*:

Pulley Size*:

No longer available  

The Gen II 2.3 L TVS has been replaced by the Gen3 2.65 L

The VMP 2.3L TVS Supercharger upgrade is a direct replacement for the factory Eaton M112 Supercharger on the 2003-2004 "Terminator" Mustang Cobra. It was designed from OEM CAD data to fit perfectly and clear the stock hood. It is the first aftermarket supercharger housing made specifically for the Terminator Cobra. It is a one piece housing with a side inlet like the factory supercharger. The one piece design makes for a very rigid housing, allows for a larger rear inlet, decreases the chance of vacuum leaks, and makes installation easier.

With the VMP TVS you get the reliability of an Eaton blower and the performance of the TVS rotorpack design. The Twin-Vortices-Series compressor has proven itself to be highly efficient over a wide operating range of 10-22+psi. It is a high twist symetrical 4-lobe rotor design with excellent adiabatic effiency. TVS technology is used on the 2013 GT500, ZR1 Corvette, and ZL1 Camaro.

Dyno Sheets(see pictures):

  • This is a gain of 165RWHP and 103RWTQ over an already modified cobra.
  • With 2.8" pulley (19psi) and Torco (approx 100 octane) 646RWHP/598RWTQ:
  • VMP TVS with a very mild pump gas tune (16*) and 3" pulley (17psi) 608RWHP/559RWTQ:

VMP 2.3L TVS Supercharger upgrade key features:

  • Direct replacement for stock supercharger
  • Gains of 100-350RWHP depending on pulley size & boost level
  • 1 year warranty provided by VMP
  • Proven Eaton reliability: 100,000 mile service interval
  • Pre-filled with oil
  • Intercooler bolts directly to bottom of blower
  • Side inlet for easy access to fuel rails
  • Side inlet allows use of different throttle body styles
  • Vacuum line connections and T-MAP in factory locations
  • Large 45MM bypass-valve for cooler operation, improved driveably, and greater fuel efficiency
  • EGR Option available
  • Pulleys are easily bolted on and off using six allen head bolts

Package Includes:

  • VMP TVS Blower with stainless steel 6-bolt hub
  • One interchangeable 6-bolt pulley of your choice
  • Inlet elbow for your throttle body style
  • Six M6x14MM bolts for pulley
  • Eight M6x25MM bolts for elbow
  • Ten M5x16MM intercooler bolts
  • O-ring for inlet elbow
  • Loctite
  • Four new intercooler transfer tube O-rings
  • Contoured EGR spacer allows mounting of EGR valve on rear of blower.
  • Includes one pulley, additional pulleys available.


  • The factory supercharger to lower intake manifold gasket is metal and can be re-used in most cases
  • The factory IAC gasket may be re-used in most cases
  • The TB gasket may be re-used in most cases, aftermarket TBs usually include a new gasket
  • EGR Option available

Click here to download VMP 03-04 Cobra TVS Instructions (Rev 3.1.15)

Instruction supplements:

Boost levels:

SC Pulley Stock Crank 4lb lower
3.3" 14psi 18psi
3.2" 15psi 19psi
3.0" 17psi 22psi


stroker or cammed motors only
2.6" 21psi stroker or cammed motors only

Add a VMP fueling upgrade kit for just $799 with a VMP TVS purchase (click here)!

This is a complete package for 03-04 Cobra's with an upgraded supercharger such as the VMP TVS. Good for 550-700rwhp. Above that we recommend a return fuel system.

Set of eight Siemens-Deka 60lb injectors with the correct USCAR connector
VMP 18v fuel pump booster, easy 2 wire installation
VMP 3000 MAF sensor good for 800RWHP, choose small footprint for stock housing or large footprint for JLT High-boost
These are the only other upgrades required when installing a VMP TVS on your 03-04 Cobra with a 3.2"-2.5" pulley, 3.3" pulley can be ran on stock fuel.

The VMP TVS places the SC pulley in the same location as the stock blower.

For specific belt lenghts click here: Cobra Bob's 2003-2004 Cobra Belt Selection Guide

The VMP TVS was designed with a HUGE inlet, the throttle body you choose to run with the blower will ultimately determine how much air you can get into the blower and how well it performs. We support all major throttle body styles including a custom GT500 bolt-pattern single blade throttle body. If you don't have an upgraded throttle body already you may order one from us, make sure you select the correct elbow style to match up with the Idle Air Control valve.

VMP GT500 Monoblade TB

BBK Dual 65MM Cobra TB (stock-style round IAC passage)

Accufab Single Blade Cobra TB (polished) (slot IAC passage)

Lightning Force Performance Single Blade Cobra TB (billet or black) (slot IAC passage)

The VMP TVS accepts all factory hardware

The VMP TVS deletes the boost dump solenoid and EGR mounting bracket for a cleaner look and larger inlet.

The VMP TVS uses a removeable inlet elbow for easy fuel rail access and compatibility with many styles of throttle bodies

The VMP TVS has all of the factory vacuum connections and T-MAP mounting pad on the rear

The VMP TVS has a one-piece housing with integral intercooler mounting flange and 45mm bypass

A factory style bypass valve actuator is located directly on the blower.

The VMP TVS uses an o-ring on the inlet elbow for easy installation and servicing.

The VMP TVS has a Monster inlet as standard equipment.

The elbow on the VMP TVS has the two bottom holes slotted to faciliate easier installation and removal.

Several elbows are available for the VMP TVS to support the Dragon, stock 57mm, BBK 65mm, Accufab, LFP, Billetflow, and GT500 bolt-pattern throttle bodies

Dragon requires an IAC mount (included), the others use an round or slotted IAC passage like stock.

VMP TVS 03-04 Cobra supercharger upgrade with 2.8" pulley, stock lower, and agressive pump gas tune VS stock M112 blower with a 2.8" pulley

For Off-Road use only.